1、flexural modulus

flexural modulus發音

英：　　美：

flexural modulus中文意思翻譯

常用釋義：彎曲模量：材料在彎曲時所表現出的剛度

[力]彎曲模量；[力]撓曲模量

撓[彎]曲模量

flexural modulus雙語使用場景

1、The results show that the addition of mica can enhance the flexural strength, flexural modulus, notched Izod impact strength and heat deformation temperature of the composites;───結果表明：云母可有效提高PP的彎曲強度及模量、懸臂梁缺口沖擊強度和耐熱性能；

2、Paper and board - Testing of cores - Determination of natural frequency and flexural modulus by experimental modal analysis───紙和紙板.硬紙板錐形圓筒的檢驗.試驗?zāi)Ｐ头治龇y定自然頻率和彎曲模量

3、Alkaline treatment of wood flour makes flexural strength and flexural modulus of the composite decrease by 20.───木粉的堿化處理使復合材料的彎曲強度和彎曲模量分別下降20。

4、The flexural strength and flexural modulus decreased with the increasing amount of ABS.───合金的彎曲強度和彎曲模量都隨著合金中ABS用量的升高而下降。

5、Preparation and flexural modulus of biodegradable composites reinforced with kenaf fibers───洋麻纖維增強全降解復合材料的制備及其彎曲模量

6、The flexural modulus of mechanization and automation of the structural design of shallow knowledge───機械化與自動化彎曲模的結構設計淺識

7、The results showed that the tensile strength, flexural strength and flexural modulus increased obviously with increase of amount of Mica.───結果表明，復合材料的拉伸強度、彎曲強度和彎曲模量隨著云母用量的增加而提高。

8、Experimental results show that the flexural modulus increases with the increases of the fibre content and length.───實驗表明，隨著纖維含有量和纖維長度的增加，材料彎曲模量呈遞增趨勢。

flexural modulus相似詞語短語

1、Young's modulus───楊氏模量

2、elastic modulus───彈性系數；彈性模數

3、bulk modulus───[力]體積彈性模量

4、electrical stimulus───電刺激

5、lunar modules───n.[航]登月艙

6、lunar module───n.[航]登月艙

7、shear modulus───剪切模量；剪切彈性模數

2、沙比克 PC 123R-WH5C051X

供應商提醒你，UL rated HB as of 10/97. 200 series recommended when V-2 rating required. Nonhalogenated. 17.5 MFR, for small, intricate parts. UV stabilized.

Property

TYPICAL PROPERTIES (1)

MECHANICAL Value Unit Standard

Tensile Stress, yld, Type I, 50 mm/min 630 kgf/cm² ASTM D 638

Tensile Stress, brk, Type I, 50 mm/min 660 kgf/cm² ASTM D 638

Tensile Strain, yld, Type I, 50 mm/min 7 % ASTM D 638

Tensile Strain, brk, Type I, 50 mm/min 110 % ASTM D 638

Flexural Stress, yld, 1.3 mm/min, 50 mm span 940 kgf/cm² ASTM D 790

Flexural Modulus, 1.3 mm/min, 50 mm span 23900 kgf/cm² ASTM D 790

Hardness, Rockwell M 70 - ASTM D 785

Hardness, Rockwell R 118 - ASTM D 785

Taber Abrasion, CS-17, 1 kg 10 mg/1000cy ASTM D 1044

IMPACT Value Unit Standard

Izod Impact, unnotched, 23°C 326 cm-kgf/cm ASTM D 4812

Izod Impact, notched, 23°C 70 cm-kgf/cm ASTM D 256

Tensile Impact, Type S 557 cm-kgf/cm² ASTM D 1822

Falling Dart Impact (D 3029), 23°C 1728 cm-kgf ASTM D 3029

THERMAL Value Unit Standard

Vicat Softening Temp, Rate B/50 154 °C ASTM D 1525

HDT, 0.45 MPa, 6.4 mm, unannealed 137 °C ASTM D 648

HDT, 1.82 MPa, 6.4 mm, unannealed 132 °C ASTM D 648

CTE, -40°C to 95°C, flow 6.84E-05 1/°C ASTM E 831

Specific Heat 1.25 J/g-°C ASTM C 351

Thermal Conductivity 0.19 W/m-°C ASTM C 177

Relative Temp Index, Elec 100 °C UL 746B

Relative Temp Index, Mech w/impact 100 °C UL 746B

Relative Temp Index, Mech w/o impact 100 °C UL 746B

PHYSICAL Value Unit Standard

Specific Gravity 1.2 - ASTM D 792

Specific Volume 0.83 cm³/g ASTM D 792

Density 1.19 g/cm³ ASTM D 792

Water Absorption, 24 hours 0.15 % ASTM D 570

Water Absorption, equilibrium, 23C 0.35 % ASTM D 570

Water Absorption, equilibrium, 100°C 0.58 % ASTM D 570

Mold Shrinkage, flow, 3.2 mm (5) 0.5 - 0.7 % SABIC Method

Melt Flow Rate, 300°C/1.2 kgf 17.5 g/10 min ASTM D 1238

OPTICAL Value Unit Standard

Light Transmission, 2.54 mm 88 % ASTM D 1003

Haze, 2.54 mm 1 % ASTM D 1003

Refractive Index 1.586 - ASTM D 542

ELECTRICAL Value Unit Standard

Volume Resistivity >1.E+17 Ohm-cm ASTM D 257

Dielectric Strength, in air, 3.2 mm 14.9 kV/mm ASTM D 149

Relative Permittivity, 50/60 Hz 3.17 - ASTM D 150

Relative Permittivity, 1 MHz 2.96 - ASTM D 150

Dissipation Factor, 50/60 Hz 0.0009 - ASTM D 150

Dissipation Factor, 1 MHz 0.01 - ASTM D 150

Hot Wire Ignition {PLC) 4 PLC Code UL 746A

High Voltage Arc Track Rate {PLC} 2 PLC Code UL 746A

High Ampere Arc Ign, surface {PLC} 1 PLC Code UL 746A

Comparative Tracking Index (UL) {PLC} 2 PLC Code UL 746A

FLAME CHARACTERISTICS Value Unit Standard

UL Recognized, 94HB Flame Class Rating (3) 0.76 mm UL 94

UV-light, water exposure/immersion F1 - UL 746C

Source GMD, last updated:2000/01/04

Processing

Parameter

Injection Molding Value Unit

Drying Temperature 120 °C

Drying Time 3 - 4 hrs

Drying Time (Cumulative) 48 hrs

Maximum Moisture Content 0.02 %

Melt Temperature 280 - 305 °C

Nozzle Temperature 275 - 300 °C

Front - Zone 3 Temperature 280 - 305 °C

Middle - Zone 2 Temperature 270 - 295 °C

Rear - Zone 1 Temperature 260 - 280 °C

Mold Temperature 70 - 95 °C

Back Pressure 0.3 - 0.7 MPa

Screw Speed 40 - 70 rpm

Shot to Cylinder Size 40 - 60 %

Vent Depth 0.025 - 0.076 mm

Source GMD, last updated:2000/01/04

THESE PROPERTY VALUES ARE NOT INTENDED FOR SPECIFICATION PURPOSES.

PLEASE CONTACT US FOR AVAILABILITY IN YOUR REGION.

(1) Typical values only. Variations within normal tolerances are possible for various colors. All values are measured after at least 48 hours storage at 23°C/50% relative humidity. All properties, except the melt volume and melt flow rates, are measured on injection molded samples. All samples tested under ISO test standards are prepared according to ISO 294.

(2) Only typical data for selection purposes. Not to be used for part or tool design.

(3) This rating is not intended to reflect hazards presented by this or any other material under actual fire conditions.

(4) Internal measurements according to UL standards.

(5) Measurements made from laboratory test coupon. Actual shrinkage may vary outside of range due to differences in processing conditions, equipment, part geometry and tool design. It is recommended that mold shrinkage studies be performed with surrogate or legacy tooling prior to cutting tools for new molded article.

(6) Needs hard coat to consistently pass 60 sec Vertical Burn.

Disclaimer : THE MATERIALS, PRODUCTS AND SERVICES OF SAUDI BASIC INDUSTRIES CORPORATION (SABIC) OR ITS SUBSIDIARIES OR AFFILIATES (“SELLER”) ARE SOLD SUBJECT TO SELLER’S STANDARD CONDITIONS OF SALE, WHICH ARE AVAILABLE UPON REQUEST. INFORMATION AND RECOMMENDATIONS CONTAINED IN THIS DOCUMENT ARE GIVEN IN GOOD FAITH. HOWEVER, SELLER MAKES NO EXPRESS OR IMPLIED REPRESENTATION, WARRANTY OR GUARANTEE (i) THAT ANY RESULTS DESCRIBED IN THIS DOCUMENT WILL BE OBTAINED UNDER END-USE CONDITIONS, OR (ii) AS TO THE EFFECTIVENESS OR SAFETY OF ANY DESIGN OR APPLICATION INCORPORATING SELLER’S MATERIALS, PRODUCTS, SERVICES OR RECOMMENDATIONS. UNLESS OTHERWISE PROVIDED IN SELLER’S STANDARD CONDITIONS OF SALE, SELLER SHALL NOT BE RESPONSIBLE FOR ANY LOSS RESULTING FROM ANY USE OF ITS MATERIALS, PRODUCTS, SERVICES OR RECOMMENDATIONS DESCRIBED IN THIS DOCUMENT. Each user is responsible for making its own determination as to the suitability of Seller’s materials, products, services or recommendations for the user’s particular use through appropriate end-use and other testing and analysis. Nothing in any document or oral statement shall be deemed to alter or waive any provision of Seller’s Standard Conditions of Sale or this Disclaimer, unless it is specifically agreed to in a writing signed by Seller. Statements by Seller concerning a possible use of any material, product, service or design do not, are not intended to, and should not be construed to grant any license under any patent or other intellectual property right of Seller or as a recommendation for the use of any material, product, service or design in a manner that infringes any patent or other intellectual property right.